Eddie AI
EddieDaVinci Resolve

DaVinci Resolve · Audio

How to fix audio crackling in DaVinci Resolve

Updated 8 stepsFor DaVinci Resolve

The short answer

Open DaVinci Resolve > Preferences > System > Video and Audio I/O, check that the I/O Engine and Output Device are the hardware you listen on. For clicks at cuts or when playback starts, check that Enable Soft Fades and Enable Ramp Up on Play are on in File > Project Settings > Fairlight. If it only crackles in busy sections, cache or bypass heavy plugins on the Fairlight page. If there's no sound at all, check the speaker button and the track Mute and Solo buttons first.

Faders and knobs on an audio mixing console.
Photo by James Kovin on Unsplash

8 steps

In DaVinci Resolve

  1. 01Check what's muted
  2. 02Check the audio device
  3. 03Keep Soft Fades and Ramp Up on
  4. 04Cache heavy clip plugins
  5. 05Bypass track plugins to test
  6. 06Keep audio first on the Edit page
  7. 07When it crackles while recording
  8. 08Fix clicks in the file itself
  1. 01

    Check what's muted

    For no sound at all, look at the far right of the Edit page toolbar: the audio Enable/Disable button turns playback on and off. On the Fairlight page, the speaker icon next to the transport controls turns red when audio is muted. Then check each track's Mute (M) and Solo buttons; soloing a track silences every track that isn't soloed.

  2. 02

    Check the audio device

    Open DaVinci Resolve > Preferences > System > Video and Audio I/O. Under Audio I/O, I/O Engine sets the hardware Resolve uses for audio: System Audio, Desktop Video, Fairlight Audio Accelerator, or ASIO on Windows. With System Audio, set Output Device to the speakers or headphones you're using, and Input Device to your mic. Playback processing buffer size sets the size of the playback buffer, and the readout to its right shows the approximate latency in milliseconds. Blackmagic's manual doesn't give a buffer size for fixing crackle. The only size it names is for Apple spatial audio (ASAF) mixes: 256 samples or more, with 1,024 recommended, because sizes below 256 samples produce errors.

  3. 03

    Keep Soft Fades and Ramp Up on

    Open File > Project Settings > Fairlight. Enable Soft Fades adds a 1.5 ms (72 samples) crossfade between adjacent timeline clips to prevent clicks or pops during playback. It's on by default; if someone turned it off, check it again. Enable Ramp Up on Play fades your mix in to prevent clicks whenever playback starts. The default ramp-up time is 2.1 ms, and you can set it up to 100 ms.

  4. 04

    Cache heavy clip plugins

    On the Fairlight page, right-click a clip with a plugin on it and choose Cache Audio Effects. The effect is baked into a cache, the clip gets a cache badge, and you can still change the plugin. Or choose Export Audio Files to bounce the clip with the effect to a new layer above the original.

  5. 05

    Bypass track plugins to test

    In the Fairlight Mixer, turn off a channel strip's Effects In button. When it's unlit, that track's Fairlight FX, AU and VST plugins are bypassed. If the crackle stops, one of them is the cause. Voice Isolation, Dialogue Leveler and the built-in EQ and Dynamics are not affected by it.

  6. 06

    Keep audio first on the Edit page

    In the Edit page viewer's option menu, leave Show All Video Frames off. Off, the default, puts audio first and drops video frames when the computer can't keep up. On, audio quality is compromised so that every frame plays.

  7. 07

    When it crackles while recording

    Record buffer size sits under Playback processing buffer size, with its own latency readout. To hear whether the crackle is in the take or only in what you monitor, choose Fairlight > Input Monitor Style > Repro: while recording, you hear what has just been recorded, played back from the track.

  8. 08

    Fix clicks in the file itself

    If the click is in the recording, zoom all the way into the clip on the Fairlight page until the samples show as points, then drag a point up or down, or drag across several to redraw the waveform. Right-click the clip and choose Reset Edited Samples to undo it. For a click at a cut, a crossfade brings both sides to the zero crossing.

Good to know

Before you start

Note 1
Blackmagic's manual has no fix for crackle that happens only on the Fairlight page, or for playback that stops after you plug in or unplug headphones. For the headphone case, check that Output Device still names the device you're listening on.
Note 2
A higher project sample rate costs more: 96 kHz uses twice the processing power of 48 kHz. You can only change Audio Sample Rate (File > Project Settings > Fairlight) before the project's first timeline is created.
Note 3
The manual describes no plugin for removing crackle from a whole recording. For clicks in a file, sample editing is what it documents.
Note 4
Muting or soloing affects the render too: muted tracks, and the tracks a solo silences, are left out of the output.

Eddie AI

Do it in Eddie

Eddie can't change how Resolve plays or records audio. Fix crackle in Resolve's own settings.

Eddie's audio cleanup removes wind, hum, background noise or music from under the voice; it isn't described as a click or crackle fix. The cleaned audio plays in Eddie and is used in its MP4 renders, while the Resolve project (.drp) keeps the original sound.

Back to Resolve

Open the edit, click Export and choose Resolve. The default is a Resolve project (.drp) that opens with the timeline built; behind the arrow is a Resolve FCPXML you bring into the project you have open with File > Import > Timeline. In the desktop app, Send to DaVinci Resolve builds the timeline in the Resolve you have running, through Eddie's script (Workspace > Scripts > Eddie AI AE).

If you imported the footage through the desktop app, the timeline points at your original camera files. If you uploaded on the web or pulled from cloud storage, it points at Eddie's proxy media: relink to those in the Media Pool with Relink Selected Clips, not to the camera originals.

Try it in Eddie freeNew accounts start with 500 free credits. No card required.

FAQ

Questions

Why does audio crackle only on the Fairlight page?
Blackmagic's manual doesn't say. For heavy plugins it suggests Cache Audio Effects or exporting the clip with the effect baked in. Also check the Output Device in Video and Audio I/O, and that Enable Soft Fades and Enable Ramp Up on Play are on in Project Settings > Fairlight.
Why is there no sound on the Edit page?
Check the audio Enable/Disable button at the far right of the toolbar, then the track Mute and Solo buttons, then the Output Device in Preferences > System > Video and Audio I/O.
Why does my audio crackle when I record a voiceover?
Check Record buffer size in Video and Audio I/O, and use Fairlight > Input Monitor Style > Repro to hear whether the crackle is in the take or only in the monitoring.
Do muted or soloed tracks still render?
No. A muted track, and every track a solo silences, is left out of the rendered output.

Let Eddie do the DaVinci Resolve busywork

Add your footage, say what you want, and send the cut back to your editor. New accounts start with 500 free credits. No card required.